Használati útmutató Skil 2531 AB Fúró-csavarozó

Használati útmutató

9

8 Do not dispose of the charger together with

household waste material

9 Do not dispose of the battery together with

household waste material

WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):

• Do not connect the blue (= neutral) or brown (= live) wire

in the cord of the charger to the earth terminal of the plug

• If for any reason the old plug is cut o the cord of the

charger, it must be disposed of safely and not left

unattended

USE

• Combined switch A 2 for on/o and speed control

Control the speed steplessly from zero to maximum by

putting less or more pressure on the trigger

• Charging battery 0

- connect charger to power source as illustrated 0a

- green light B will turn on indicating that the charger is

ready for operation 0a

- insert battery into charger as illustrated 0b

! the battery can also remain in the tool while

charging; in that case the tool cannot be switched

on

- green light B will blink indicating that the battery is

being charged 0c

- after approximately 1 hour the battery is fully charged

and green light B stays on after blinking 0d

! remove battery from charger after charging

period has ended thereby lengthening the service

life of the battery

IMPORTANT:

- if green light B does not blink after inserting a battery,

this may mean that the battery is too cold or too hot

(charger only charges batteries when its temperature

is between 0°C and 45°C) 0e

- the lithium-ion battery can be charged at any time

(interrupting the charging procedure does not damage

the battery)

- the lithium-ion battery does not have to be empty

before charging (no “memory-eect” as with

nickel-cadmium batteries)

- while charging, the charger and the battery may

become warm to touch; this is normal and does not

indicate a problem

- ensure that the outside surface of the battery is clean

and dry before inserting into charger

- do not charge at temperatures below 0°C and over

45°C; this will seriously damage the battery as well as

the charger

- do not remove battery from tool while it is running

- if you anticipate long periods of non-use for the tool, it

is best to unplug the charger from its power source

- when the lithium-ion battery is empty, the tool is

switched o automatically

- a signicantly reduced working period after charging

indicates that the battery is worn out and should be

replaced

• Changing direction of rotation !

- when not properly set in left/right position, switch A 2

cannot be activated

! change direction of rotation only when tool is at a

complete standstill

• Changing bits @

- insert the bit as deep as possible in the chuck

! do not use bits with a damaged shank

• Torque control (VariTorque) #

- output torque will increase as clutch ring C is rotated

from 1 to 19; position D will lock up the clutch to permit

drilling or driving heavy duty work

- when turning in a screw, rst try VariTorque position 1

and increase until the desired depth has been reached

• Mechanical gear selection $

- set selector F to desired speed

! actuate the gear selector while tool is running

slowly

LOW

- low speed

- high torque

- for screwdriving and drilling large diameters

- for tapping thread

HIGH

- high speed

- lower torque

- for drilling small diameters

• Battery protection

Switches o the tool automatically when

1) the load is too high

2) the battery temperature is not within the allowable

operating temperature range of -10 to +60°C

3) the lithium-ion battery is nearly empty (to protect

against deep discharge)

! do not continue to press the on/off switch after

the tool is switched off automatically; battery may

be damaged

• Spot light G %

Spot light G automatically lights on when activating

switch A 2

• Holding and guiding the tool ^

! while working, always hold the tool at the

grey-coloured grip area(s)

- keep ventilation slots H 2 uncovered

- do not apply too much pressure on the tool; let the tool

do the work for you

APPLICATION ADVICE

• Use the appropriate bits &

! only use sharp bits

• When drilling ferrous metals

- pre-drill a smaller hole, when a large hole is required

- lubricate drill bit occasionally with oil

• When turning in a screw at/near the cross cut end or an

edge of wood, pre-drill a hole in order to avoid cracking of

the wood

• For an optimal use of the tool a steady pressure on the

screw is required, especially while removing

• When screwdriving in hard wood one should pre-drill a

hole

• Splinterfree drilling in wood *

• Dustfree drilling in walls (

• Dustfree drilling in ceilings )

• Drilling in tiles without skidding ¡

• For more tips see www.skil.com

Értékelés

További információ erről a kézikönyvről

Megértjük, hogy jó, ha van egy papíralapú kézikönyv a Skil 2531 AB Fúró-csavarozó-hoz. A kézikönyvet bármikor letöltheti weboldalunkról, és saját maga is kinyomtathatja. Ha szeretne egy eredeti kézikönyvet, javasoljuk, hogy lépjen kapcsolatba a következővel: Skil. Esetleg tudnak adni egy eredeti kézikönyvet. Más nyelvű kézikönyvet keres Skil 2531 AB Fúró-csavarozó készülékéhez? Válassza ki a kívánt nyelvet a honlapunkon, és keresse meg a modellszámot, hátha elérhető.

Műszaki adatok

Skil Fúró-csavarozók összes kézikönyve
Fúró-csavarozók további kézikönyvei

Gyakran Ismételt Kérdések a következővel kapcsolatban: Skil 2531 AB Fúró-csavarozó

Ügyfélszolgálati csapatunk keresi a hasznos termékinformációkat, és válaszol a gyakran ismételt kérdésekre. Amennyiben pontatlanságot talál a gyakran ismételt kérdésekben, a kapcsolatfelvételi űrlapon jelezze nekünk a hibát.

Kapcsolódó termékek

Használati útmutató

Skil 2432 AG Fúró-csavarozó

Használati útmutató

Skil 2017 AA Fúró-csavarozó

Használati útmutató

Skil 2842 AD Fúró-csavarozó

Használati útmutató

Skil 2830 AA Fúró-csavarozó

Használati útmutató

Skil 3080 JA Fúró-csavarozó

Használati útmutató

Skil 3070 EB Fúró-csavarozó

Használati útmutató

Skil 3085 HB Fúró-csavarozó

Használati útmutató

Skil 3010 HB Fúró-csavarozó

Kapcsolódó kategóriák