Használati útmutató Makita PC5001C Betondaráló

Használati útmutató

7

30. Do not use the tool on any materials

containing asbestos.

31. Do not use water or grinding lubricant.

32. Ensure that ventilation openings are kept clear

when working in dusty conditions. If it should

become necessary to clear dust, first

disconnect the tool from the mains supply

( use non metallic objects ) and avoid

damaging internal parts.

SAVE THESE INSTRUCTIONS.

WARNING:

DO NOT let comfort or familiarity with product

(gained from repeated use) replace strict adherence

to safety rules for the subject product. MISUSE or

failure to follow the safety rules stated in this

instruction manual may cause serious personal

injury.

FUNCTIONAL DESCRIPTION

CAUTION:

• Always be sure that the tool is switched off and

unplugged before adjusting or checking function on

the tool.

Switch action

Fig.1

CAUTION:

• Before plugging in the tool, always check to see

that the switch trigger actuates properly and

returns to the "OFF" position when released.

For tool with the lock-on switch

To start the tool, simply pull the switch trigger (A).

Release the switch trigger to stop. For continuous

operation, pull the switch trigger (A) and then push in the

lock lever (B). To stop the tool from the locked position,

pull the switch trigger (A) fully, then release it.

For tool with the lock-off switch

To prevent the switch trigger from accidentally pulled, a

lock lever is provided. To start the tool, push in the lock

lever (B) and then pull the switch trigger (A). Release the

switch trigger to stop.

For tool with the lock on and lock-off switch

To prevent the switch trigger from accidentally pulled, a

lock lever is provided. To start the tool, push in the lock

lever (B) and then pull the switch trigger (A). Release the

switch trigger to stop. For continuous operation, push in

the lock lever (B), pull the switch trigger (A) and then

push in the lock lever (B) further. To stop the tool from

the locked position, pull the switch trigger (A) fully, then

release it.

Electronic function

Constant speed control

• Possible to get fine finish, because the rotating

speed is kept constantly even under the loaded

condition.

• Additionally, when the load on the tool exceeds

admissible levels, power to the motor is reduced to

protect the motor from overheating. When the load

returns to admissible levels, the tool will operate as

normal.

Soft start feature

• Soft start because of suppressed starting shock.

Indication lamp

Fig.2

The indication lamp lights up green when the tool is

plugged. If the indication lamp does not light up, the

mains cord or the controller may be defective. The

indication lamp is lit but the tool does not start even if the

tool is switched on, the carbon brushes may be worn out,

or the controller, the motor or the ON/OFF switch may be

defective.

Unintentional restart proof

Even locking lever keeping the switch trigger depressed

(Lock-on position) does not allow the tool to restart even

when the tool is plugged.

At this time, the indication lamp flickers red and shows

the unintentional restart proof device is on function.

To cancel the unintentional restart proof, pull the switch

trigger fully, then release it.

Level planing (for PC5001C only)

Fig.3

To level a surface, the base of the planer should be

aligned with the diamond wheel. The front roller should

be adjusted (use hex wrench) upward to the level

required for the desired stock removal amount.

To change the amount of stock (concrete) removed,

loosen the hex socket head bolts on the base holder with

the hex wrench. Raise or lower the front roller to adjust

the gap between it and the diamond wheel. The

difference is the stock removal amount. Then secure the

hex socket head bolts very carefully.

Fig.4

NOTE:

• Maximum stock removal should be less than 4.0

mm.

Tilting base for smoother planing ( for

PC5001C only)

Fig.5

For smooth removal of a given surface roughness or

texture, tilting the base is helpful. Use the hex wrench to

loosen the two hex socket head bolts securing the base

on either side.

Use a hex wrench to lower the three hex socket head

bolts on the base by turning them on the base clockwise.

Fig.6

Use a square or ruler to obtain the desired base angle in

relation to the diamond wheel. Then secure carefully the

hex socket head bolts on either side of the base. Adjust

Értékelés

További információ erről a kézikönyvről

Megértjük, hogy jó, ha van egy papíralapú kézikönyv a Makita PC5001C Betondaráló-hoz. A kézikönyvet bármikor letöltheti weboldalunkról, és saját maga is kinyomtathatja. Ha szeretne egy eredeti kézikönyvet, javasoljuk, hogy lépjen kapcsolatba a következővel: Makita. Esetleg tudnak adni egy eredeti kézikönyvet. Más nyelvű kézikönyvet keres Makita PC5001C Betondaráló készülékéhez? Válassza ki a kívánt nyelvet a honlapunkon, és keresse meg a modellszámot, hátha elérhető.

Műszaki adatok

Makita Betondarálók összes kézikönyve
Betondarálók további kézikönyvei

Kapcsolódó termékek

Használati útmutató

Makita PC5000C Betondaráló

Használati útmutató

Flex LD 24-6 180 Betondaráló

Használati útmutató

Flex LD 18-7 125 Betondaráló

Kapcsolódó kategóriák