Használati útmutató Bosch GLI 18V-2200 C Lámpa

Használati útmutató

12 | English

Assembly

Battery Charging (seefigureB)

Note: The battery is supplied partially charged. To ensure

full battery capacity, fully charge the battery in the charger

before using your tool for the first time.

The lithium-ion battery can be charged at any time without

reducing its service life. Interrupting the charging process

does not damage the battery.

The lithium-ion battery is protected against deep discharge

by the Electronic Cell Protection (ECP). A protective circuit

switches the cordless worklight off when the battery is

drained.

u Do not continue to press the on/off switch after the

worklight has been automatically switched off. This

can damage the battery. Ensure that the battery is

charged and that the cordless worklight has cooled down

before switching the cordless worklight on again.

To remove the battery(14), press the release button(13)

and pull the battery out of the cordless worklight. Do not use

force to do this.

Follow the instructions on correct disposal.

Putting the Button Cell into Operation

(seefigureB)

Remove the separating film between the button cell(11)

and the button cell contact when using the tool for the first

time.

The cordless worklight is fitted with a button cell so that it

can be detected by the mobile device even if no battery(14)

is inserted.

Unlock the locking mechanism of the battery cover(2) and

fold up the battery cover(3).

Unscrew the screw of the battery compartment cover(9)

and remove the battery compartment cover(10).

Remove the film from the button cell contact and reattach

the battery compartment cover with the screw.

Operation

Start-up

Inserting the Battery

Unlock the locking mechanism of the battery cover (2) and

fold up the battery cover (3).

Insert the charged battery (14) into the lamp head (4) until

you feel it engage and it is flush with the lamp head (4).

Close the battery cover (3) and then the locking mechanism

of the battery cover (2).

u Make sure that the rubber lip is seated correctly when

closing the battery cover. Otherwise protection against

dust and splash water will not be ensured.

Setting up

Carefully fold out the stand(5) and place the cordless work-

light on the floor. Make sure it is secure.

Fastening to the tripod

You can use the tripod mount (7) to screw the cordless

worklight onto a tripod.

Tighten the 5/8" screw. Ensure that the tripod has a firm

footing.

Swivelling the Lamp Head (see figure A)

The lamp head (4) is attached to the carrying handle (8).

The lamp head can be set to five different positions using the

carrying handle.

Switching On/Off

To start up the cordless worklight, press the on/off switch

(1).

To switch off the cordless worklight, press the on/off switch

(1) again.

Adjusting the Brightness

Press the on/off switch (1) briefly to switch on the cordless

worklight with maximum brightness. To adjust the bright-

ness in two stages, hold down the on/off switch (1) until the

required brightness is reached.

Temperature-dependent overload protection

When the permitted operating temperature is exceeded, the

cordless worklight initially reduces the brightness before

switching itself off if required for protection. Let the cordless

worklight cool down and then switch the cordless worklight

back on.

Changing the Button Cell (seefigureB)

u Make sure that the battery compartment(12) is not

damaged when removing the cell.

u Make sure that the positive pole of the button cell

faces upwards.

A warning will be displayed in the app before the button

cell(11) is fully used up.

To change the button cell(11), unlock the locking mechan-

ism of the battery cover(2) and fold up the battery

cover(3).

Unscrew the screw of the battery compartment cover(9)

and remove the battery compartment cover(10).

Remove the empty button cell and insert a new button cell.

Reattach the battery compartment cover with the screw.

Battery charge indicator

The green LEDs on the battery charge indicator indicate the

state of charge of the battery. For safety reasons, it is only

possible to check the state of charge when the power tool is

not in operation.

Press the button for the battery charge indicator or to

show the state of charge. This is also possible when the bat-

tery is removed.

If no LED lights up after pressing the button for the battery

charge indicator, then the battery is defective and must be

replaced.

1 609 92A 634 | (11.11.2020) Bosch Power Tools

Értékelés

További információ erről a kézikönyvről

Megértjük, hogy jó, ha van egy papíralapú kézikönyv a Bosch GLI 18V-2200 C Lámpa-hoz. A kézikönyvet bármikor letöltheti weboldalunkról, és saját maga is kinyomtathatja. Ha szeretne egy eredeti kézikönyvet, javasoljuk, hogy lépjen kapcsolatba a következővel: Bosch. Esetleg tudnak adni egy eredeti kézikönyvet. Más nyelvű kézikönyvet keres Bosch GLI 18V-2200 C Lámpa készülékéhez? Válassza ki a kívánt nyelvet a honlapunkon, és keresse meg a modellszámot, hátha elérhető.

Műszaki adatok

Bosch Lámpák összes kézikönyve
Lámpák további kézikönyvei

Gyakran Ismételt Kérdések a következővel kapcsolatban: Bosch GLI 18V-2200 C Lámpa

Ügyfélszolgálati csapatunk keresi a hasznos termékinformációkat, és válaszol a gyakran ismételt kérdésekre. Amennyiben pontatlanságot talál a gyakran ismételt kérdésekben, a kapcsolatfelvételi űrlapon jelezze nekünk a hibát.

Kapcsolódó termékek

Használati útmutató

Bosch GLI PortaLED 136 Lámpa

Használati útmutató

Bosch GLI PortaLED 102 Lámpa

Használati útmutató

Bosch GLI 12V-330 Lámpa

Használati útmutató

Bosch GLI 18V-1200 C Lámpa

Használati útmutató

Bosch GLI PortaLED 238 Lámpa

Használati útmutató

Eglo 900834 Lámpa

Használati útmutató

Eglo 99759 Lámpa

Használati útmutató

Livarno IAN 380120 Lámpa

Kapcsolódó kategóriák